PrintClose   
                

Finlay I-120RS

General Equipment & Supplies, Inc.

Sales Department
4300 Main Ave
PO Box 2145
Fargo, North Dakota, 58103
USA
OFFICE +1 701 282-2662 FAX +1 (701) 364-2190
TOLL FREE (800) 437-2924
FINLAY I-120RS 
Aggregate Impact Crushers
2018
Contact DealerSend to a FriendHotlist (5)No Pics
SAY YOU SAW THIS ON EQUIPMENTLOCATOR.COM!!!
AVAILABILITY AND PRICE SUBJECT TO CHANGE AND/OR PRIOR SALE. SPECIFICATIONS AND EQUIPMENT CONFIGURATION IS SUBJECT TO CHANGE. PLEASE CONSULT A SALES PROFESSIONAL TO ENSURE THAT WEBSITE INFORMATION IS CORRECT AND UP-TO-DATE.
EQUIP. LOCATION
Fargo, North Dakota, USA
STOCK #E00054459SERIAL#TRX120RSAOMIB8520AVAILABLEImmediately
MAKEFinlayCATEGORYFor SalePRICE
745000 USD
745000
MODELI-120RSSTATUSOn Rent
YEAR2018CLASSUsed
NOTES
  • FINLAY I-120RS EQUIPPED AS PER BELOW:

    ENGINE
    - TIER 4 FINAL /STAGE IV : SCANIA DC9 257KW (350 HP) ENGINE

    IMPACT
    - TEREX CR038 IMPACT CHAMBER

    CHAMBER:
    - FULLY HYDRAULICALLY ASSISTED APRON SETTING AND HYDRAULIC APRON RELEASE
    - MANUAL RAISECHAMBER FLAP ALLOWING EXTRA INLET CLEARANCE
    - 4 BAR ROTOR - MARTENSITIC BLOW BARS 2 HIGH & 2 LOW
    - DIRECT DRIVE VIA CLUTCH
    - DRIVE BELT TENSIONER WHEEL
    - BLOW BAR LIFTING TOOL SUPPLIED
    - TIP SPEED RANGE 36-45 M/SEC (118-148 FT./SEC).
    - SMALLER ENGINE CHAMBER DRIVE PULLEY TO GIVE A ROTOR TIP SPEED RANGE OF 32-40
    M/SEC (105-131 FT./SEC). STANDARD LARGE PULLEY STILL DISPATCHED WITH MACHINE.
    - HYDRAULIC RAISE OF CHAMBER INLET FLAP
    - ROTOR FITTED WITH 2 FULL HIGH CHROME & 2 LOWMARTENSITIC BLOW BARS

    HOPPER & FEEDER:
    - VGF FIXED HOPPER
    - STEPPED GRIZZLY FEEDER WITH INTEGRAL PRE-SCREEN STANDARD 50MM SPACING
    - MESH APERTURE ON GRIZZLY FEEDER: 38MM
    - SELECTABLE DISCHARGE TO BY-PASS CONVEYOR OR MAIN CONVEYOR
    - INDEPENDENT PRE-SCREEN C/W HYDRAULICALLY FOLDING AND LOCKING HOPPER AND
    BLANKING
    - MAT. 50MM CASSETTE SPACING & 38MM MESH AS STANDARD - MESH APERTURES AVAILABLE
    UPON REQUEST
    - INDEPENDENT PRE-SCREEN HOPPER EXTENSIONS
    - PRE-SCREEN PUNCH PLATE OPTIONAL SPACING - 38MM 50MM 63MM OR 75MM

    MAIN CONVEYOR:
    - 1100MM (43.3") BELT FULL LENGTH
    - UNDER CRUSHER VIBRATORY FEEDER WITH WEAR RESISTANT STEEL LINERS (C/W SHORTENED
    MAIN CONVEYOR)

    AUXILIARY CONVEYORS:
    - HYDRAULIC RAISE/ LOWER FOR MAGNET
    - PIPED FOR OVER BAND MAGNET
    - BYPASS CONVEYOR WITH 600MM WIDE PLAIN BELT DISCHARGING TO THE LHS OF THE
    MACHINE.
    - TWIN POLE OVER BAND MAGNET C/W STAINLESS STEEL SKIRTING & STAINLESS STEEL
    DISCHARGE CHUTE DISCHARGING TO RHS OF THEMACHINE.

    RS COMPONENTS:
    - 3.66M X 1.52M (12- X 5-) TWO DECK AFTER SCREEN C/W 50MM TOP DECK AND 40MM
    BOTTOM DECK MESH AS STANDARD UNLESS OTHERWISE STATED
    - 500MM (20") WIDE BELT SINGLE TRANSFER CONVEYOR COLLECTING MATERIAL FROM BOTH
    DECKS.
    - 500MM (20") WIDE BELT HYDRAULIC FOLDING RE-CIRCULATING CONVEYOR ABLE TO SLEW
    FOR STOCKPILING OVERSIZE MATERIAL
    - 1400MM (55") WIDE BELT FINES CONVEYOR
    - RAPID DETACH AFTER SCREEN SYSTEM FOR FLEXIBILITY.
    - BELT WEIGHER
    - ADDITIONAL DUST COVER ON FINES CONVEYOR
    - ADDITIONAL TRANSFER CONVEYOR FOR COLLECTING MATERIAL FROM EACH INDIVIDUAL DECK
    OF SCREEN BOX

    CLIMATE SPEC:
    - STANDARD OILS - (RECOMMENDED FOR AMBIENT TEMPERATURES BETWEEN -5 TO +30°C)

    DUST SUPPRESSION:
    - PIPEDFOR DUST SUPPRESSION C/W SPRAY BARS

    ELECTRICAL:
    - EMERGENCY STOPS
    - HAND HELD TRACK CONTROL SET WITH CONNECTION LEAD
    - T-LINK TELEMETRY SYSTEM FITTED C/W 3 YEARS DATA SUBSCRIPTION
    - RADIO REMOTE SYSTEM: OPERATIONAL CONTROLS OF MACHINE (AUTO START/STOP) & TRACK
    MOVEMENT
    - PRESSURIZED AIR SYSTEM FOR ELECTRICAL CONTROL CABINET

    SAFETY GUARDS IN COMPLIANCE WITH MACHINERY DIRECTIVE