PrintClose   
                

Superior 6203-ADWP

General Equipment & Supplies, Inc.

Sales Department
4600 Valley Industrial Blvd S
Shakopee, Minnesota, 55379
USA
OFFICE +1 952 224-1500 FAX +1 (952) 224-1570
TOLL FREE (800) 966-1455
LANGUAGES SPOKEN English
Contact DealerSend to a FriendHotlist (5)Show All Pics (7)
SAY YOU SAW THIS ON EQUIPMENTLOCATOR.COM!!!
AVAILABILITY AND PRICE SUBJECT TO CHANGE AND/OR PRIOR SALE. SPECIFICATIONS AND EQUIPMENT CONFIGURATION IS SUBJECT TO CHANGE. PLEASE CONSULT A SALES PROFESSIONAL TO ENSURE THAT WEBSITE INFORMATION IS CORRECT AND UP-TO-DATE.
EQUIP. LOCATION
Shakopee, Minnesota, USA
STOCK #E00053525SERIAL#1321695AVAILABLEImmediately
MAKESuperiorCATEGORYFor SalePRICE
465000 USD
465000
MODEL6203-ADWPSTATUSOn Rent
YEAR2018CLASSUsed
NOTES
  • (1) - SUPERIOR 6203-ADWP AGGREDRY WASH PLANT EQUIPPED AS PER BELOW:

    CARRIER CHASSIS:
    - MAIN FRAME CONSTRUCTED OF WIDE FLANGE STRUCTURAL STEEL BEAMS
    - QUAD AXLE WITH (16) 11X22.5 RADIAL TIRES SPRING SUSPENSION
    - COMPLETE AIRE BRAKE SYSTEM WITH MUDFLAPS TRAVEL LIGHTS WITH BRAKE AND
    DIRECTIONAL SIGNALS
    - FIFTH WHEEL HITCH
    - CRANK-DOWN LANDING GEAR 2-SPEED
    - (6) FIXED STRUCTURAL STEEL CRIBBING LEGS
    - GREASE PACKAGE - CONSISTING OF 1-2 LOCATION TO GREASE ENTIREPLANT

    SUPERIOR GUARDIAN 6203 HORIZONTAL VIBRATING SCREEN:
    - 40 HP TEFC 1200 RPM 480 VOLT 3 PHASE 60 HZ SCREEN DRIVE MOTOR
    - COIL SPRINGS
    - RIGHT HAND DRIVE
    - 5- PANELS
    - SUBFRAME
    - SPRAY SYSTEM
    - FEED BOX WITH 1/4" AR LINERS

    SUPERIOR 36" TWIN FINE MATERIAL WASHER:
    - (2) 15 HP TEFC 1800 RPM 480 VOLT 3 PHASE 60 HZ ELECTRIC MOTORS
    - 1/4" ASTM A36 STEEL
    - OUTBOARD PILLOW BLOCK BEARINGS
    - OVER-FLOW FLUME WITH ADJUSTABLE WEIR
    - MATERIAL DISCHARGE CHUTE
    - TAIL END FEED HOPPER AND TUB BAFFLE
    - VARIABLE SPEED
    - URETHANE WEAR SHOES
    - SPIRAL TYPE SHAFT HALF PITCH FLIGHTED FOR HICH CAPACITY WITH ADJUSTABLE
    MOUNTS
    - WEIR WATER OVERFLOW DOWNSPOUT ON EACH SIDE OF FINE MATERIAL WASHER
    - V-BELT DRIVE WITH GUARD
    - DODGE SHAFT MOUNT GEAR BOX

    SUPERIOR 5- X 10- SINGLE DECK DEWATERING SCREEN:
    - (2) 11.4 HP 1800 RPM ELECTRIC VIBRATORS WITH ADJUSTABLE COUNTER WEIGHTS
    230/480V/3PH/60HZ
    - ADJUSTABLE FROM 3.2G TO 6.4G AT 60HZ
    - ADJUSTABLE MOTOR SLIDE TO FIND CENTER OF GRAVITY FOR VARIOUS BED ANGLES
    - RIGID WELDED FRAME CONSTRUCTED OF 1/2 A36 STEEL
    - SINGLE-MEMBER WELDMENT UTILIZING HEAVY PIPE CROSS MEMBERS FOR A BASE WHICH
    SUPPORTS REINFORCED STEEL U-CHANNELS
    - HEAVY STEEL COMPRESSION SPRINGS
    - ADJUSTABLE FROM -5 TO +5 DEGREES
    - 1- X 2- REPLACEABLE URETHANE 0.25MM APERATURE SNAP-DECK
    - 1- X 4- X 1.25" RUBBER BOLT-ON SIDE (TO FIT LENGTH)

    ROLL-AWAY SCREEN DISCHARGE CHUTES WITH BLENDINGGATES:
    - ROLLERS MOUNTED UNDER CHUTE SUPPORT STRUCTURE
    - CONSTRUCTED OF 1/4" MILD STEEL WITH 1/4" AR400 LINER
    - DESIGNED TO MOVE DISCHARGE CHUTES AWAY FROM THE SCREEN
    - ALLOWS FOR ACCESS TO THE FRONT OF SCREEN FOR MAINTENANCE
    - (4) FLOP GATES IN EACH CHUTE; EACH GATE MANUALLY OPERATED BY A LEVER OUTSIDE
    THEIR RESPECTIVE CHUTE
    - TOP DECK CHUTE DISCHARGES OVER THE KINGPIN END OF THE CHASSIS OR ONTO MIDDLE
    DECK CROSS CONVEYOR 25% BLENDING GATES
    - MIDDLE DECK CHUTE DISCHARGES ONTO MIDDLE OR BOTTOM DECK CROSS CONVEYOR 25%
    BLENDING GATES
    - BOTTOM DECK CHUTES DISCHARGES ONTO BOTTOM OR "BLENDS UP" TO MIDDLE DECK CROSS
    CONVEYOR 25% BLENDING GATES
    - AR LINERS ON BOTH SIDES OF BLENDING GATES

    (2) 30" X 12- LONG REVERSING CROSS CONVEYORS:
    - 7.5 HP MOTOR V-BELT DRIVE WITH DRIVE GUARD
    - STRUCTURAL STEEL CHANNEL MAIN FRAME
    - MOUNTED ON ROLLERS TO MANUALLY MOVE TO DISCHARGE FROM EITHER SIDE OF CHASSIS
    - RECEIVE OVERSIZE MATERIAL FROM RESPECTIVE MIDDLE AND BOTTOM DECKS
    - CLASS II HEAD END DRIVE
    - DODGE SHAFT MOUNT REDUCER
    - HEAD PULLEY - 10" DIAMETER DRUM CROWN FACE 3/8" DIAMOND LAGGING
    - TAIL PULLEY - 10" DIAMETER WING PULLEY
    - SHAFTS TURNED AND POLISHED
    - DODGE BEARINGS
    - MANUAL SCREW TAKE UPS
    - CARRY IDLERS - C5 20 DEGREES TROUGH CHANNEL MOUNT SPACED 26"OC
    - BELTING - 3-PLY 3/16" X 1/16" 330 PIW
    - VULCANIZED BELT SPLICE
    - SUPERIOR EXTERRA PRIMARY BELT CLEANER

    UNDERSCREEN FLUME:
    - 1/4" AR CONSTRUCTION
    - SPRAY BAR AT FEED AND DISCHARGE END
    - DIRECTS FINES MATERIAL FROM SCREEN INTO FMW

    SPRAY BARS:
    - (16) 1.5" GALVANIZED SPRAY BARS AND ELBOWS BRASS NOZZLES
    - FLEXIBLE RUBBER HOSING FROM MANIFOLD TO SPRAY BARS
    - MANUALLY ADJUSTABLE SPRAY BAR FOR EACH SPRAY BAR MOUNTED BELOW WALKWAY

    WATER MANIFOLD:
    - 8" BOLT FLANGE AT GROUND LEVEL FOR FRESH WATER HOOKUP
    - FRESH WATER FEEDS IN FROM END
    - DISTRIBUTES WATER TO: SPRAY BARS SLURRY HOPPER FMW WASH BACK FINES HOPPER
    AND BOOST PUMP

    BOOST PUMP:
    - 7.5 HP ELECTRIC MOTOR 480V 3 PHASE
    - 3" CAST IRON WATER PUMP

    WYE STRAINER:
    - BOLT-ON WYE STRAINER FOR FRESH WATER SUPPLY TO PREVENT DEBRIS FROM ENTERING
    WASH SYSTEM

    SLURRY HOPPER:
    - HYDRAULICALLY FOLDS FROM TRANSPORT TO OPERATING POSITION
    - ACCEPTS FEED FROM CONVEYOR AND FEEDS ONTO FEEDBOX OF SCREEN LINED FOR WEAR
    PROTECTION
    - SPRAY BARS MOUNTED INSIDE HOPPER
    - DOUBLE ROW OF HIGH FLOW SPRAYNOZZLES TO SLURRY MATERIAL

    WALKWAY:
    - 3/16" DIAMOND TREAD PLATE ALONG BOTH SIDES AND FEED END OF SCREEN
    - 3/16" DIAMOND TREAD PLATE ALONG DISCHARGE CHUTE FOR EASIER ACCESS TO THE
    BLENDING GATES AND DISCHARGE CHUTE
    - INCLUDES TOEBOARD AND TWO-RAIL HANDRAIL BOLT ON
    - WALKWAY ACCESS ON BOTH SIDES OF THE CHASSIS WITH STEEP ANGLE STAIR ACCESS
    - DRAIN HOLES

    HYDRAULIC "LIFT ONLY" LEVELING JACKS:
    - (4) 6" X 20" HYDRAULIC CYLINDERS
    - (4) MANUAL LEVER VALVES; (1) FOR EACH CYLINDER
    - 12 VOLT HYDRAULIC PUMPING UNIT

    ADDITIONAL SPECIFICATIONS:
    - PAINT: STANDARD SUPERIOR PAINT - WINDOW GRAY (RAL 7040) FOR SCREEN WINDOW
    GRAY (RAL 7040) FOR AGGRE-DRY CHASSIS PAINTED GRAPHITE GRAY (RAL 7024)
    ORANGE GUARDING CATWALKS HANDRAILS AND LADDERS
    - GUARDING: FOR DRIVE AND TAIL PULLEYS V-BELT DRIVE AND RETURN IDLERS. GUARDS
    MAY NOT MEET ALL LOCAL CODES; CUSTOMER IS RESPONSIBLE TO HAVE GUARDING
    INSPECTED

    AES ELECTRICAL SWITCHGEAR FOR 6X20 AGGREDRY WASH PLANT:
    - 60X48 NEMA 4 ENCLOSURE WITH BACK PANEL EQUIPPED AS FOLLOWS:
    - 400 AMP MAIN CIRCUIT BREAKER WITH ROTARY OPERATOR LOCKABLE
    - CUSTOM LEG KIT AND WELDED UPPER LEG SECTIONS
    - DRIP SHIELD
    - ILLUMINATED E-STOP OPERATOR
    - MANUALLY OPERATED SIGNAL START UP HORN
    - HOUR METER
    - ALL CONTROLS INSTALLED IN ENCLOSURE DOOR
    - (3) 100 FOOT LENGTH RUNS OF 250W POWER SUPPLY CABLE
    - (1) 100 FOOT LENGTH RUN OF 4/0W EQUIPMENT GROUND
    - (1) NEMASIZE 3 FVNR MOTOR STARTER SCREEN MOTOR - 40HP
    - (2) NEMA SIZE #2 (OR #1) FOR 11.4 HP DEWATER SCREEN MOTORS- SINGLE BUTTON
    START
    - (1) ABB ACS850 30 HP VARIABLE FREQUENCY DRIVE TO OPERATE TWIN 15 HP SCREW
    MOTORS WITH POTENTIOMETER SPEED CONTROL
    - (4) NEMA SIZE 2 FVNR MOTOR STARTERS SPARE 1-4- 20HP EACH WIRED TO 60 AMP
    HUBBELL RECEPTACLES.
    - (2) NEMA SIZE 1 FVNR MOTOR STARTERS CROSS CONVEYOR 1 AND 2 7.5HP EACH
    - (1) NEMA SIZE #1 7.5 HP FVNR-BOOST PUMP
    - (1) 100 AMP FEED BREAKER WIRED TO A 100 AMP HUBBELL RECEPTACLE.
    - (1) 60 AMP FEED BREAKER WIRED TO A 60 AMP HUBBELL RECEPTACLE.
    - 5 KVA TRANSFORMER EXTERNALLY MOUNTED.
    - (1) 120 VOLT 20 AMP GFCI DUPLEX RECEPTACLE INSTALLED IN WEATHERPROOF BOX AND
    COVER