SUPERIOR 6203-T36 (TWIN 36" WASH PLANT) EQUIPPED AS PER BELOW: PLANT SPECIFICATIONS: - CONSTRUCTION: MAIN FRAME CONSTRUCTED OF WIDE FLANGE STRUCTURAL BEAMS - DISCHARGE CHUTE: MANUAL ROLLAWAY CHUTE CONSTRUCTED OF 1/4" SCTRUCTURAL STEEL WITH 1/4" WELD-IN AR 400 LINER - BLENDING CAPABILITY: 1/4 PANEL BLENDING TO GATES IN DISCHARGE CHUTE SYSTEM" - TOP DECK: OVER KING PIN OR DOWN TO MIDDLE - MIDDLE DECK: ONTO CROSS CONVEYOR OR DOWN TO BOTTOM - BOTTOM DECK: ONTO CROSS CONVEYOR OR UP TO MIDDLE DECK - WALKWAY: WALKWAY AROUND BOTH SIDES AND FEED END OF SCREEN EXTENDS OUT TO THE END OF THE DISCHARGE CHUTE - OBSERVATION PLATFORM: NOT INCLUDED - WALKWAY ACCESS: ACCESS TO BOTH SIDES OFCHASSIS WITH (2) FOLDING STEEP ANGLE STAIRS - ACCESS GATES: (2) SWING GATES - SLURRY HOPPER: SCREEN FEED SLURRY HOPPER FOLDS HYDRAULICALLY FOR TRANSPORT WITH (2) 2.5" WATER LINES - WYE STRAINER: BOLT-ON WYE STRAINER FOR FRESH WATER SUPPLY TO PREVENT DEBRIS FROM ENTERING WASH SYSTEM - GREASE PACKAGE: NOT INCLUDED - TOOL BOX: 48" X 12" X 16" ALUMINUM TOOL BOX - SAFETY TIEOFF: - OVERHEAD SAFETY TIE OFF POSTS WITH CABLE BETWEEN TWO POSTS CHASSIS SPECIFICATIONS: - AXLE: TRIDEM AXLE WITH (12) 11RX22.5 RADIAL TIRES - SUSPENSION: SPRING SUSPENSION - BRAKES: COMPLETE AIR BRAKE PACKAGE - FIFTH WHEEL: INCLUDED - LIGHTS: BRAKE AND DIRECTIONAL SIGNALS - MUD FLAPS: INSTALLED BEHIND TRANSPORT WHEELS - CRIBBING LEGS: (6) FIXED STRUCTURAL STEEL CRIBBING LEGS - LANDING GEAR: (4) HYDRAULIC LIFT-ONLY LEVELING LEGS WITH 9 HP HONDA POWER UNIT - TOW EYE: NOT INCLUDED - LEVEL ASSIST: NOT INCLUDED SPRAY SYSTEM ANDUNDERFLUME: - UNDERFLUME CONSTRUCTION: 1/4" AR PLATE - UNDERFLUME SPRAY BARS: LOCATED AT FEED AND DISCHARGE END - MANIFOLD: 8" BOLT FLANGE FOR FRESH WATER HOOK UP (CUSTOMER RESPONSIBLE FOR FRESH WATER PLUMBING TO MANIFOLD) - MANIFOLD DISTRIBUTION: DISTRIBUTES WATER TO SCREEN SPRAY BARS SLURRY HOPPER FMW WASH BACK AND FINES HOPPER CROSS CONVEYOR SPECIFICATIONS: - CROSS CONVEYORS: (2) 30" X 12- LONG SLIDE-IN REVERSING CROSS CONVEYORS - DRIVE: CLASSI HEAD END - GEAR REDUCER: DODGE SHAFT MOUNT - MOTOR: 7.5 HP MOTORS TEFC - DRIVE PULLEY: 10" DIAMETER DIAMOND LAGGED CEMA CROWN FACED DRUM - TAIL PULLEY: 10 DIAMETER CEMA CHEVRON WING PULLEY - BEARINGS: DODGE - IDLERS: CEMAC 5" DIA. ROLLS SEALED FOR LIFE BALL BEARINGS 20 DEGREE - BELTING: 3-PLY 3/16 X1/16 330 PIW - BELT SPLICE: FACTORY VULCANIZED BELT SPLICES - BELT SCRAPER: (1) SUPERIOR EXTERRA PRIMARY SCRAPER PER CROSS CONVEYOR SCREEN SPECIFICATIONS: - SCREEN SIZE: GUARDIAN 6X20 3-DECK HORIZONTAL SCREEN - SCREEN DRIVE: RIGHT HAND - CONFIGURATION: OPERATE IN TRUE HORIZONTAL POSITION - SCREEN MOTOR: MOUNT MANIFOLD SPRAY BARS AND HOSES ONTO BASE FRAME - FOLDING MOTOR: MANUALLY FOLDING MOTOR FOR PLANT TO TRAVEL AT 12- 6" WIDE - SHAFT HOUSING: MILD STEEL PROTECTION CLAMPED TO SHAFT HOUSING - SPRINGS: STANDARD COIL SPRINGS - FEEDBOX: 24" FEEDBOX WITH 1/4" AR LINERS - SIDELINERS: STANDARD SCREEN SIDE-LINERS - SCREEN MEDIA: CUSTOMER SUPPLIED TOP DECK: - TOP DECK TYPE: HEAVY X-BRACE SINGLE CROWN DECK TO ACCOMMODATE 5- SINGLE CROWN WIRE CLOTH MEDIA SECTIONS - TOP TAKE UP: STANDARD TAKE UP RAILS - TOP CROSS MEMBER PROTECTORS: NOT INCLUDED MIDDLE DECK: - MIDDLE DECK TYPE: HEAVY X-BRACE SINGLE CROWN DECK TO ACCOMMODATE 5- SINGLE CROWN WIRE CLOTH MEDIA SECTIONS - MIDDLE TAKE UP: STANDARD TAKE UP RAILS - MIDDLE CROSS MEMBER PROTECTORS: NOT INCLUDED BOTTOM DECK: - BOTTOM DECK TYPE: HEAVY X-BRACE SINGLE CROWN DECK TO ACCOMMODATE 5- SINGLE CROWN WIRE CLOTH MEDIA SECTIONS - BOTTOM TAKE UP: STANDARD TAKE UP RAILS - BOTTOM CROSS MEMBER PROTECTORS: NOT INCLUDED MATERIAL WASHER SPECIFICATIONS: - MATERIAL WASHER: SUPERIOR TWIN 36" X 25- FINE MATERIAL WASHER - SCREW SPEED: 20 RPM - CAPACITY: UP TO 200 STPH (SUBJECT TO CHANGE BASED ON FINAL GRADATION) - WEAR SHOES: RUBBER - CHANGED TO NI-HARD (12-21-21) - SCREW MOTOR: (2) 15 HP TEFC - GEAR BOX: DODGE SHAFT MOUNT PAINTING: - STANDARD SUPERIOR PAINT: PAINTED GRAPHITE GRAY (RAL 7024) WITH SAFETY YELLOW HANDRAILS GUARDS AND LADDERS AES ELECTRICAL SWITCHGEAR FOR 6X20 WASHPLANT: - 60X48 NEMA 4 ENCLOSURE WITH BACK PANEL EQUIPPED AS FOLLOWS: - 400 AMP MAIN CIRCUIT BREAKER WITH ROTARY OPERATOR LOCKABLE - CUSTOM LEG KIT AND WELDED UPPER LEG SECTIONS - DRIP SHIELD - 800 WATT PANEL HEATER - ILLUMINATED E-STOP OPERATOR - MANUALLY OPERATED SIGNAL START UP HORN - HOUR METER - ALL CONTROLS INSTALLED IN ENCLOSURE DOOR - (1) NEMA SIZE 3 FVNR MOTOR STARTER SCREEN MOTOR - 40HP - (1) ABB ACS850 30 HP VARIABLE FREQUENCY DRIVE TO OPERATE TWIN 15 HP SCREW MOTORS WITH POTENTIOMETER SPEED CONTROL - (4) NEMA SIZE 2 FVNR MOTOR STARTERS SPARE 1-4- 20HP EACH WIRED TO 60 AMP HUBBELL RECEPTACLES. - (2) NEMA SIZE 1 FVNR MOTOR STARTERS CROSS CONVEYOR 1 AND 25HP EACH - (1) 100 AMP FEED BREAKER WIRED TO A 100 AMP HUBBELL RECEPTACLE. - (1) 60 AMP FEED BREAKER WIRED TO A 60 AMP HUBBELL RECEPTACLE. - 5 KVA TRANSFORMER EXTERNALLY MOUNTED. - (1) 120 VOLT 20 AMP GFCI DUPLEX RECEPTACLE INSTALLED IN WEATHERPROOF BOX AND COVER - 100- OF MAIN POWER CORD GUARDING: - GUARDING: FOR DRIVE AND TAIL PULLEYS V-BELT DRIVE AND RETURN IDLERS. GUARDS MAY NOT MEET ALL LOCAL CODES; CUSTOMER IS RESPONSIBLE TO HAVEGUARDING INSPECTED.