MINE DUTY PORTABLE 7- X 20- - 3 DECK SUPERIOR SCREEN PLANT WITH (3) CROSS CONVEYORS AND 48" FEED CONVEYOR: SUPERIOR 7203-38HBS MEDIUM SCALPING SCREEN: - 50 HP 1200 RPM - 2.5 DEGREE SLOPE - MEDIUM SCALPER TOP DECK - SIDE TENSION MIDDLE DECK - END TENSIONED BOTTOM DECK - 4- CLAMP BARS - RIGHT HAND DRIVE - COIL SPRINGS 3 AXLE CARRIER: - 18" WF BEAM 60#. - HUTCH 61" SPAN EQUALIZING SUSPENSION. - 22 500# STANDARD FORGE AXLES 11:00R X 22.5 TIRES. - AIR BRAKES BRAKE LIGHTS MARKER LIGHTS REFLECTOR TAPE AND MUD FLAPS. 60" X 30- UNDER SCREEN CONVEYOR 20 HP SEW RIGHT ANGLE DRIVE: - 42" SPACING ON CEMA C IDLERS. - VULCANIZED LAGGED HEAD PULLEY SELF-CLEANING WING TAIL PULLEY. - 3 PLY BELT; VULCANIZED SPLICE - SUPERIOR BELT SCRAPER - SEW RIGHT ANGLE DRIVE 1/4" PLATE UNDER SCREEN HOPPER WITH WEAR STRIPS & ADJUSTABLE SKIRT BOARD WIPERS. PRODUCT CHUTES: - 2ND DECK OVERS: BUILT OF 1/4" PLATE W/HEAVY DUTY 9" X 18" RUBBER LINERS IN WEAR AREA (FLOOR). WITH 1/3-2/3 REMOVABLE PANELS TO TAKE PRODUCT TO 3RD DECK CROSS CONVEYOR. 3RD DECK OVERS: - BUILT OF 1/4" PLATE W/HEAVY DUTY 9" X 18" RUBBER LINERS IN IMPACT WEAR AREA (FLOOR) AND 3/8" AR ON SIDE WEAR AREAS. SCREEN DISCHARGE CHUTE WITH HEADY DUTY 9" X 18" RUBBER LINERS. IN FLOOR AND 3/8" AR ON SIDE OF WEAR AREAS. 30" X 13-6" MINE DUTY CROSS CONVEYOR FOR TOP DECK OVERS: - 7.5 HP SEW RIGHT ANGLE DRIVE - CANOE LINERS. (CANOE LINERS INCLUDED) - 3 PLY BELTING. - CLOSE SPACING CEMA C5 RUBBER IMPACT CHANNEL INSERT IDLERS. - VULCANIZE SPLICE - STD WIPER 30" X 13-6" CROSS CONVEYOR FOR 2ND DECK OVERS: - 7.5 HP SEW RIGHT ANGLE DRIVE - CEMA C4 STEEL CAN CHANNEL INSETIDLERS AT 30" CENTERS. - 3 PLY BELTING - DODGE SCM BEARINGS. - VULCANIZED SPLICE - STD WIPER 30" X 13-6" CROSS CONVEYOR FOR 3RD DECK OVERS: - 7.5 HP SEW RIGHT ANGLE DRIVE - CEMA C4 STEEL CAN CHANNEL INSET IDLERS AT 30" CENTERS. -3 PLY BELTING - DODGE SCM BEARINGS. - VULCANIZED SPLICE - STD WIPER 48" FEED CONVEYOR W/ 25 HP SEW RIGHT ANGLE DRIVE WITH ADJUSTABLE FEED HEIGHT: - 25 HP SEW RIGHT ANGLE DRIVE 16" LAGGED DRIVE PULLEY WITH TYPE E BEARINGS - SELF-CLEANING MINE DUTY 14" WING TAIL PULLEY WITH DODGE SCM BEARINGS. - 3 PLY BELT IMPACT IDLERS IN FEED AREA THEN 36" SPACING ON CEMA C IDLERS - 7 IMPACT IDLERS IN FEED AREA - FORMED SKIRT BOARD 1ST 15-. - VULCANIZE SPLICE. - SUPERIOR XTERRA BELT SCRAPER. - PRECISION 16" XT35 CERAMIC HEAD PULLEY VS STD. XT 35 RUBBER LAGGED. - HD PPI IMPACT SYSTEM IN LOAD ZONE OF FEED CONVEYOR - 25 HP SEW RIGHT ANGLE DRIVE. 20" DIAMOND PLATE FOLD DOWN WALK WAYS BOTH SIDES OF SCREEN 48BACK PLATFORM TOE BOARDS 42" TUBESTEEL HANDRAILS AND ACCESS LADDER. EQUIPPED FOR SLIDE-IN-REJECT CONVEYOR CAPABILITY SAFETY GUARDS SANDBLASTED CHASSIS RUST INHIBITOR PRIMER AND TWO FINISH COATS OF PAINT INCLUDED. OPTIONS INCLUDED: HYDRAULIC LIFT AT HEAD END OF FEED CONVEYOR. HYDRAULIC LIFT AT TAIL END OF FEED CONVEYOR. PIN LOCATIONS AT DIFFERENT LEVELS. FAB-TEC PLANT MOUNTED 48K RUN-ON SYSTEM: - 5 X 24" CYLINDERS 48 000 LB. CAPACITY (AT 2500 PSI) WITHSAFETY-LOK CIRCUIT - 1 SPOOL VALVE - NUMBER OF BANKS TO MATCH LEG QUANTITY - CYLINDER MOUNTING PLATES & HARDWARE - HD FOOT PADS SELF CONTAINED HONDA 8 HP HYD. POWER PACKAGE ~VS~ HPX 200 12V: ELECTRIC START: - ELECTRIC START - 12 GALLON HYDRAULIC RESERVOIR WITH FILTER PROTECTION. - 2 1/2 GPM PUMP. - VULCANIZED SPLICE ON ALL CONVEYORS. (1)60" (1) 42" (3)30" - GE STYLE MOUNTING FOR REJECT CONVEYOR. - RUBBER DISC RETURNS ~VS~ STEEL CANS. - ORANGE GUM RUBBERFLASHING ON ALL CONVEYORS - TOOL BOX MOUNTED ON CHASSIS. - 3/8" TIE OFF CABLES INSTALLED ON UPPER SECTION OF FEED CONVEYOR ON BOTH SIDES AND ON TOP DECK CROSS CONVEYER ON BOTH SIDES. - 48" SUPERIOR X-TERRA BELT SCRAPER ON FEED CONVEYOR. - 60" SUPERIOR X-TERRA BELT SCRAPER ON UNDER-SCREEN CONVEYOR - HD PPI IMPACT SYSTEM IN LOAD ZONE OF FEED CONVEYOR - LED LIGHTS - FABTEC BASE FRAME AES SG PANEL FOR A FABT/SUPE 7203-38MSOF SCREEN PLANT ELECTRICAL SWITCHGEAR WITH 125FT POWER CORD. MAIN BREAKER WITH LOCKABLE OPERATOR 50 HP FVNR FOR SCREEN 20 HP FVNR FOR UNDER SCREEN CONVEYOR (3) 7.5 HP FVNR FOR CROSS CONVEYORS (1) 3 HP FVNR FOR REJECT WITH 20 AMP RECEPTACLE (1) 25 HP FVNR FOR OVERHEAD FEED (2) 20 HP SPARES WITH 60 AMP HUBBELL RECEPTACLES (1) 100 AMP FEED BREAKER WITH 100 AMP HUBBELL RECEPTACLE PANEL STAND HOUR METER SAFETY START HORN E-STOP SAFETY PLACARDS. 150FT PENDANT CORD WITH PUSH BUTTONS. PANEL SETS OFF THE PLANT APPOX 25- FOR OPERATION GUARDING - WE DO NOT WARRANT THATMANUFACTURERS›¼À™ GUARDING WILL MEET ALL LOCAL CODES. IT IS THE RESPONSIBILITY OF THE END USER TO HAVE GUARDING CHECKED BY A LOCAL INSPECTOR PRIOR TO STARTUP OF EQUIPMENT OPERATIONS CORRECTIVE ACTIONS AND ASSOCIATED EXPENSE ARE THE RESPONSIBILITY OF THE END USER.