FABTEC/SUPERIOR PORTABLE P400 CONE PLANT WITH 48" SIDE FOLD CONE CONVEYOR AND 42" FEED CONVEYOR WITH SURGE BIN PAN FEEDER EQUIPPED PER THE BELOW: - SUPERIOR P400 CONE - MOUNTING PROVISION FOR HYDRAULIC CONSOLE - 400 HP @ 1200 RPM TOSHIBA TEFC CONE MOTOR: (5010UZ FRAME) REVERSE CRUSHER MOTOR ENCLOSED DRIVE BELT GUARD AND BELT DRIVE: - INSPECTION/ CLEANOUT DOORS - WALK-IN STYLE INCORPORATED WITH OBSERVATION DECK HEAVY DUTY CONE MOUNT AND AR LINED UNDER CONE DISCHARGE HOPPERWITH 1/2" X 6" ADJUSTABLE WIPERS STANDARD CONE FEED RING WITH EXPANDED METAL WINDOWS -STANDARD HOLD-DOWN BRACKETS INCLUDED 48" - REVERSIBLE SIDE-FOLD UNDER CONE CONVEYOR: - SEW KA87 15 HP RIGHT ANGLE DRIVE ~VS~ CONVENTIONAL DRIVE - INCLUDES TYPE ›¼ÀœE›¼À BEARINGS ON HEAD PULLEY - 14›¼À VULCANIZED LAGGED HEAD PULLEY 12›¼À SELF-CLEANING WING TAIL PULLEY - 3 PLY BELT 1/4" COVER 2 7/16›¼À DODGE SCM BEARINGS - CLOSE SETTING ON CEMA C IDLERS UNDER CONE THEN 36" SPACING - EXTENDED LENGTH TO BE AS LONG AS POSSIBLE WITH FOLDING HEIGHT - HYDRAULIC FOLD FOR TRANSPORT - ORANGE GUM RUBBER FLASHING - RUBBER DISC RETURNS - VULCANIZED SPLICE - SUPERIOR EXTERRA WIPER 42" X 26- CONE FEED CONVEYOR: - SEW KA87 15 HPRIGHT ANGLE DRIVE ~VS~ CONVENTIONAL DRIVE: - INCLUDES TYPE ›¼ÀœE›¼À BEARINGS ON HEAD PULLEY. - 3 PLY BELT 2 15/16›¼À DODGE SCM BEARINGS. - FAB TEC HEAVY DUTY STYLE IMPACT AREA THEN 36" SPACING ON CEMA C IDLERS. IMPACT BARS ON THE SIDEAND IMPACT ROLLERS IN THE CENTER. - 14›¼À VULCANIZED LAGGED HEAD PULLEY 12›¼À SELF-CLEANING WING TAIL PULLEY. - ORANGE GUM RUBBER FLASHING - RUBBER DISC RETURNS - VULCANIZED SPLICE - SUPERIOR EXTERRA WIPER - HYDRAULIC RAISE & LOWER OF CONE FEED CONVEYOR TO GIVE ADEQUATE CLEARANCE TO REMOVE UPPER BOWL ASSEMBLY. SURGE BIN WITH PAN FEEDER: - SIMPLICITY VM-4896 PAN FEEDER WITH SUSPENSION SPRINGS - TO FEED ONTO CONE FEED CONVEYOR - 3/8›¼À PLATE SIDES 6›¼À X 6›¼À X 1/2›¼À ANGLE AND 6/15# WFSUPPORTS - SURGE HOPPER LINED WITH TRICON TRI-BRAZE WEAR LINERS - 1/2" BOLT IN WEAR LINERS IN MIDDLE SECTIONS - 3/8" BOLT IN WEAR LINERS ON THE SIDE WALLS - HIGH ABRASION WEAR LINERS WITH COUNTERSUNK RETENTION HARDWARE TANDEM/TANDEM AXLE ARRANGEMENT: SPLIT TANDEM AXLE DESIGN WITH 24" WF 76# BEAMS: - RIDE RITE AIR RIDE SUSPENSION - 25 000# AXLES AND 11:00RX22.5 TIRES - AIR BRAKES - LED MARKER LIGHTS - LED BRAKE LIGHTS - LED STROBE LIGHT - MUD FLAPS - REFLECTIVE TAPE - SIX GROUND SUPPORT STANDS WITH JACKING LEGS PROVISION FOR 9- WIDE TRAILKING TKAB1 OR TKAB2 BOOSTER - SAFETY GUARDS SAND BLASTED CHASSIS RUST INHIBITOR PRIMER AND TWO FINISH COATS INCLUDED INCLUDED OPTIONS: - 6 LEG FAB TEC 70K RUN-ON SYSTEM KIT - 18›¼À STROKE CYLINDERS 70 000 LB. CAPACITY (AT 2500 PSI) WITH SAFETY-LOK CIRCUIT - (1) SPOOL VALVE~ NUMBER OF BANKS TO MATCH LEG QUANTITY - CYLINDER MOUNTING PLATES & HARDWARE - HEAVY DUTY FOOT PADS SELFCONTAINED HONDA 8 HP HYD. POWER PACKAGE ~VS~ HPX 200 12V: - ELECTRIC START - 12 GALLON HYDRAULIC RESERVOIR WITH FILTER PROTECTION - 2 1/2 GPM PUMP OBSERVATION STAND INCORPORATED INTO WALK-IN DRIVE GUARD: - FOR EASY CONE DRIVE MAINTENANCE AND CONE FEED OBSERVATION - A USER-FRIENDLY RECOMMENDATION - ACCESS PANELS ON 3 OUTER SIDES ADDITIONAL FRONT PLATFORM IN FRONT OF CONE MOTOR: - PLATFORMS ON EACH SIDE OF PAN FEEDER WITH HANDRAILS AND LADDERS ON BOTH SIDES - FALL PROTECTIONCABLE SYSTEM AROUND CONE FOR CONE MAINTENANCE - (2) LARGE TOOL BOXES MOUNTED ON CHASSIS SPECIAL REVERSE MOUNTED JACK SHAFT DRIVE FOR 400 HP: - RAPTOR COUPLING - (2) 4 7/16" TYPE ›¼À˜E›¼À™ BEARINGS - 4 7/16›¼À ALLOY SHAFT - ADDED STEEL FOR LOWER BEARING/ SHEAVE MOUNT - ADDED GUARDING - COGGED BELT DRIVE WITH SUPERIOR COUNTERSHAFT BLOWER FOR DRIVE PRESSURIZATION - ADJUSTABLE MAGNET STAND ON FEED CONVEYOR FOR 12PSM 6 CONE PROTECTION MAGNET ACCESS LADDER FOR MAGNET CLEANING - GUARDING - WE DO NOT WARRANT THAT MANUFACTURERS›¼À™ GUARDING WILL MEET ALL LOCAL CODES. IT IS THE RESPONSIBILITY OF THE END USER TO HAVE GUARDING CHECKED BY A LOCAL INSPECTOR PRIOR TO STARTUP OF EQUIPMENT OPERATIONS CORRECTIVEACTIONS AND ASSOCIATED EXPENSE ARE THE RESPONSIBILITY OF THE END USER