SUPERIOR 48"RZTU RAZERTAIL TRUCK UNLOADER EQUIPPED AS PER BELOW: TRUCK LOAD AREA: - GRATE: 10- X 5- OUTSIDE DIMENSION - LOAD AREA CONSTRUCTION: FLAT BAR WITH 5" WIDE OPENINGS - SELF-CLEANING RAMPS: HINGED ON EACH SIDE OF THE GRATE FOLD UP FOR CLEANING CYCLE AFTER TRUCK IS OFF RAMP - RAMP BULKHEAD: 10- WIDE BY 8-4" LONG FOLD HYDRAULICALLY FOR ROAD TRANSPORT - EXTENDED RAMPS: ELIMINATE EARTHEN RAMPS WITH 25- EXTENDED QUAD-FOLD STEEL RAMPS EACH SIDE FROM SELF-CLEANING RAMPS TO GRADE HYDRAULICALLY FOLD INTO HOPPER AREA FOR TRANSPORT 4TH RAMP FOLDED MANUALLY UNLOADING CONVEYOR: - SIZE: APPROXIMATELY 48" X 63- - DISCHARGE HEIGHT: FOLDING CONVEYOR WITH 3 POSITION ADJ HEIGHT MAXIMIM FROM BOTTOM OF DISCHARGE HOOD - FRAME: 30" DEEP TRUSS - DRIVE: CLASS 1 SINGLE WRAP - GEAR REDUCER: DODGE SHAFT MOUNT WITH BACKSTOP - MOTOR: 50 HP 1800 RPM TEFC - V-BELT DRIVE: WITH DRIVE GUARD - CAPACITY: 1000 STPH OF 100 PCF MATERIAL 1.5" MINUS SPHERICAL LUMPS - BELT SPEED: 210FPM - FLOW CONTROL: ADJUSTABLE SLIDE GATE - DISCHARGE HOOD: NOT INCLUDED - SUPERIOR IDLERS: CEMA C 5" DIAMETER ROLLS SEALED FOR LIFE BALL BEARINGS - LOAD AREA: 5" DIAMETER FLAT STEEL IDLERS CLOSE SPACING - TROUGH: 35 DEGREE EQUAL ON 4- SPACING - RETURNS: STEEL ROLLS ON 10- SPACING - DRIVE PULLEY: 20" DIAMETER CERAMIC LAGGED DRUM - SNUB PULLEY: 18" DIAMETER CEMA CHEVRON WING - TAIL PULLEY: 12" DIAMETER MD CHEVRON WING - HEAD PULLEY: 16" DIAMETER PLAIN STEEL MD DRUM - SHAFTS: TURNED AND POLISHED - BEARINGS: DODGE - TAKE UPS: SCREW TYPE - BELTING: 3 PLY 3/16 X 1/16 330 PIW - BELT SPLICE: FACTORY VULCANIZED BELT SPLICE - BELT SCRAPER: SUPERIOR EXTERRA PRIMARY SCRAPER CHASSIS: - CHASSIS CONSTRUCTION: WELDED STEEL TUBE - AXLE: TANDEM WITH SINGLE 385/65RX22.5 TIRES - HITCH: FIFTH WHEEL - BRAKES: COMPLETE AIR BRAKE PACKAGE - LIGHTS: BRAKE AND DIRECTIONAL SIGNALS - MUD FLAPS: INSTALLED BEHIND TRANSPORT WHEELS - LANDING JACKS: HYDRAULIC LANDING LEGS WITH 12-VOLT PUMPING UNIT HYDRAULICS: - POWER UNIT: 30 HP ELECTRIC PUMPING UNIT - HYDRAULIC RAMPS: RAISE AND LOWER - HYDRAULIC CONVEYOR FOLD: 25- HYDRAULIC HEAD END FOLD ADDITIONAL SPECIFICATIONS: - VOLTAGE: 480V/3PH/60HZ - ELECTRICAL PANEL: ENCLOSURE WITH MAIN DISCONNECT CIRCUIT BREAKER PUSH BUTTON ON/OFF SWITCHES MOUNTED TO THE CHASSIS AND WIRED TO MOTORS. 100- OF MAIN POWER CORD - REMOTE CONTROL: WIRELESS REMOTE CONTROLS BELT DRIVE HYDRAULIC UNIT AND RAMP OPERATIONS - OPERATOR PLATFORM: WALKWAY AND HANDRAILS OVER CONVEYOR ON BOTH SIDES OF HOPPER AREA FOR OPERATOR WORKSTATION AND INSPECTION PLATFORM - PAINT: 1 COAT PRIMER 1 COAT FINISH ENAMEL GRAPHITE GRAY - GUARD PAINT: SAFETY YELLOW - IDLER PAINT: POWDER COATED SUPERIOR ORANGE - PATENTS: UNIT INCLUDES PATENTS - OWNERS MANUAL: (1) COPY INCLUDED FOR OPERATION AND MAINTANCE GUARDING: FOR DRIVE AND TAIL PULLEYS V-BELT DRIVE AND RETURN IDLERS. GUARDS MAY NOT MEED ALL LOCAL CODES; CUSTOMER IS RESPONSIBLE TO HAVE GUARDING INSPECTED.