SUPERIOR SENTRY 4250 CLOSED CIRCUIT HORIZONTAL SHAFT IMPACTOR PLANT EQUIPPED AS PER BELOW: CARRIER CHASSIS: - CONSTRUCTION: MAIN FRAME CONSTRUCTED OF WIDE FLANGE STRUCTURAL STEEL BEAMS - AXLE: TRIPLE AXLE WITH (12) 11RX22.5 RADIAL TIRES -BOOSTER AXLE: SINGLE AXLE WITH (4) 11RX22.5 RADIAL TIRES - FIFTH WHEEL: INCLUDED - BRAKES: COMPLETE AIRE BRAKE PACKAGE - LIGHTS: BRAKE AND DIRECTIONAL SIGNALS - MUD FLAPS: INSTALLED BEHIND TRANSPORT WHEELS - CRIBBING LEGS: (8) FIXE STRUCTURAL STEEL CRIBBING LEGS - SCREW JACKS ON KING PIN SUPPORTS - GREASE PACKAGE: REMOTE GREASE STATION MULTIPLE GREASE POINTS OUTSIDE OF CHASSIS FRAME - LANDING GEAR: QTY. (6) HYDRAULIC RUN-ON LEVELING LEGS WITH 9 HP HONDA POWER UNIT - TOOL BOX: ALUMINUM TOOL BOX - JIB CRANE: INCLUDED FOR HSI MAINTENANCE 120V POWER ; MAY NEED TO BE REMOVED FOR TRANSPORT SENTRY 4250 HORIZONTAL SHAFT IMPACTOR: - 4250 HSI CRUSHER: INSTALLED - 2 UP 2 DOWN DESIGN - BLOWBARS: MEDIUM CHROME - DRIVE SHEAVE: INSTALLED ON CRUSHER - HP REQUIREMENTS: 250 HP ELECTRIC MOTOR DRIVE SHEAVE DRIVE BELTS AND DRIVE GUARD - CRUSHER HOPPER: CRUSHER FEED CHUTE WITH CHAIN AND RUBBER CURTAIN INTREPID VIBRATING PAN FEEDER: - 4812 VPF: VIBRATING 48X12 PAN FEEDER - ELECTRIC DRIVE MOTOR QTY. (2) 8.5HP 900 RPM VIBRATING MOTORS - FEEDER ANGLE: FEEDER MOUNTED HORIZONTALLY (0 DEGREES) - REAR ACCESS LADDER TO VGF PRE-SCREEN MODULE: - PRE-SCREEN MODULE: 4- X 6- - (1) SET OF 2" FINGERS INSTALLED - SECOND SECTION WITH CARRY OVER PAN INSTALLED AT 5 DEGREES - (2) 4.3HP 900 RPM VIBRATING MOTORS - MODULE MOUNTED AT A HORIZONTAL(0 DEGREES) - FINGERS INSTALLED AT A 2.5 DEGREE SLOPE ANTHEM INCLINED SCREEN: - SCREEN SIZE: 6X162-DECK INCLINED SCREEN - DRIVE: RIGHT HAND DRIVE - CONFIGURATION: OPERATE IN INCLINED POSITION HYDRAULIC RAISE SWING DOWN LEG BOLTED FOR OPERATION - MOTOR: 30 HP 1200 RPM TEFC NEMA PREMIUM DESIGN C - SHAFT HOUSING: MILD STEEL PROTECTION CLAMPED TO SHAFT HOUSING - SPRINGS: STANDARD COIL SPRINGS - FEED BOX: 24" FEEDBOX WITH 1/4" AR LINERS - DECK: SINGLE CROWN DECK TO SUPPORT WIRE CLOTH MEDIA - SCREEN MEDIA: NOT INCLUDED UNDERCRUSHER PAN FEEDER: - FEEDER: 48" X 72" ELECTRO MECHANICAL VIBRATORY FEEDER - ELECTRIC MOTOR: QTY. (2) 2.7 HP - LINERS: REPLACEABLE 3/8" AR400 LINERS - MOUNTING POSITION: MOUNTED BELOW CRUSHER ACCEPTS FEED FROM CRUSHER AND DISCHARGES ONTO CRUSHER DISCHARGE CONVEYOR 48" CRUSHERDISCHARGE CONVEYOR: - FRAME: CHANNEL FRAME CONVEYOR DISCHARGES MATERIAL ON TO THE SCREEN - FOLD: HINGED SECTION THAT RAISES WITH THE SCREEN - HYDRAULIC ADJUST: HYDRAULIC ADJUSTABLE DISCHARGE END FOR ADDITIONAL CLEARANCE FOR SCREEN MAINTENANCE - DRIVE: 15 HP SEW RIGHT ANGLE DRIVE - DRIVE PULLEY: 14" DIAMETER CROWN FACE 3/8" HERRINGBONE LAGGED DRUM - TAIL PULLEY: 12" DIAMETER CHEVRON WING PULLEY - BEARINGS: DODGE BEARINGS: - BELTING: 3 PLY 3/16 X 1/16 330 PIW - SPLICE: FACTORY VULCANIZED BELT SPLICE - FULL LENGTH SKIRT BOARD - LOAD AREA: SUPERIOR CEMA C 5" MOXIE ROLLS - TROUGH: SUPERIOR CEMA C 5" MOXIE ROLLS - RETURNS: SUPERIOR CEMA C 5" FLAT STEEL ROLLS - TAKE UPS: MANUAL SCREW TYPE TAKE-UPS - SCRAPER: BELT CLEANER - EXTERRA PRIMARY BELT CLEANER - MAGNET: SELF-CLEANING SUSPENDED PERMANENT MAGNET 48" SCREEN FINES CONVEYOR: - CONSTRUCTION: 1/4" AR PLATE STEEL SIDES - OPERATION: RAISES AND LOWERS WITH SCREEN STRUCTURE - MATERIAL: RECEIVESSCREEN UNDERSIZE MATERIAL AND DISCHARGES OFF PLANT: - FLASHING: ADJUSTABLE RUBBER FULL LENGTH - FINES HOPPER LINER: NOT INCLUDED - CONSTRUCTION: 48" BELT WIDTH STRUCTURAL STEEL CHANNEL MAIN FRAME - DRIVE: 15 HP RIGHT ANGLE DRIVE - DRIVE PULLEY: 12" DIAMETER 3/8" HERRINGBONE LAGGED DRUM - TAIL PULLEY: 12" DIAMETER CHEVRON WING PULLEY - BEARINGS: DODGE BEARINGS - BELTING: 3 PLY 3/16 X 1/16 330 PIW - SPLICE: FACTORY VULCANIZED SPLICE - TROUGH: SUPERIOR CEMA C 5" STEEL ROLLS - RETURNS: SUPERIOR CEMA C 5" FLAT STEEL ROLLS - TAKE UPS: MANUAL SCREW TYPE TAKE-UPS - SCRAPER: BELT CLEANER - EXTERRA PRIMARY BELT CLEANER (2) 24" WIDE X 12- LONG REVERSING CROSS CONVEYORS: - FRAME: STRUCURAL STEEL CHANNEL MAIN FRAME -OPERATION: MOUNTED ANGLE IRON SLIDE TRACK TO MANUAL MOVE TO DISCHARGE FROM EITHER SIDE OF CHASSIS - MATERIAL: RECEIVES TOP AND BOTTOM DECK OVERSIZE MATERIAL - ELECTRIC MOTOR: 7.5 HP RIGHT ANGLE DRIVE - GEAR REDUCER: DODGE - DRIVE PULLEY: 10" DIAMETER DRUM CROWN FACE 3/8" DIAMOND LAGGIN - TAIL PULLEY: 10" DIAMETER WING PULLEY - BEARINGS: DODGE BEARINGS - BELTING: 3 PLY 3/16" X 1/16" 330 PIW - SPLICE: FACTORY VULCANIZED SPLICE - TROUGH: SUPERIOR CEMA C 5" STEEL ROLLS CHANNEL MOUNT - RETURNS: SUPERIOR CEMA C 5" FLAT STEEL ROLLS - TAKE UPS: MANUAL SCREW TYPE TAKE UPS - SCRAPER: BELT CLEANER - EXTERRA PRIMARY BELT CLEANER (1) 24" WIDE X 12- LONG REVERSING GRIZZLY FINES CONVEYOR: - FRAME: STRUCTURAL STEEL CHANNEL MAIN FRAME - OPERATION: MOUNTED ANGLE IRON SLIDE TRACK TO MANUALLY MOVE TO DISCHARGE FROM EITHER SIDE OF CHASSIS - MATERIAL: RECEIVES GRIZZLY FINES MATERIAL AND DISCHARGES OFF PLANT - ELECTRIC MOTOR: 4.5 HP RIGHT ANGLE DRIVE - HEAD PULLEY: 10" DIAMETER DRUM CROWN FACE 3/8" DIAMOND LAGGING - TAIL PULLEY: 10" DIAMETER WING PULLEY - BEARINGS: DODGE BEARINGS - TAKE UPS: MANUAL SCREW TAKE UPS - SUPERIOR IDLERS: CARRY IDLERS - C5 20 DEGREE TROUGH CHANNEL MOUNT SPACED 26" ON CENTER - BELTING: 3 PLY 3/16" X 1/16" 330 PIW - SPLICE: FACTORY VULCANIZED SPLICE - SCRAPER: BELT CLEANER - EXTERRA PRIMARY BELT CLEANER (1) 24" x 33- RECIRCULATION CONVEYOR: - FRAME: STRUCTURAL STEEL CHANNEL MAIN FRAME - OPERATION: HYDRAULIC RAISE AND LOWER FROM TRANSPORT TO OPERATING POSITION - MATERIAL: RECEIVES SCREEN OVERSIZE MATERIAL FROM CROSS CONVEYOR - ELECTRIC MOTOR: 10 HP RIGHT ANGLE DRIVE - DUST COVERS INSTALLED - HEAD PULLEY: 12" DIAMETER DRUM CROWNFACE 3/8" DIAMOND LAGGING - TAIL PULLEY: 10" DIAMETER WING PULLEY - BEARINGS: DODGE BEARINGS - BELTING: 3 PLY 3/16" X 1/16" 330 PIW - SPLICE: FACTORY VULCANIZED SPLICE - TROUGH: SUPERIOR CEMA C 5" STEEL ROLLS CHANNEL MOUNT - RETURNS: SUPERIOR CEMA C 5" FLAT STEEL ROLLS - TAKE UPS: MANUAL SCREW TYPE TAKE UPS - SCRAPER: BELT CLEANER - EXTERRA PRIMARY BELT CLEANER VOLTAGE: - 480V/3PH/60HZ GRIZZLY CARTRIDGE FOR PRE-SCREEN - SINGLE DECK GRIZZLY DESIGN 2" SPACING (REMOVED DUE TO FINGER SECTION INSTALLED) AES ELECTRICAL SWITCHGEAR PANEL FOR 4250CC PLANT AS PER BELOW: - 60X60 NEMA 3R/4 ENCLOSURE INSTALLED TO A CORD CAGE 800 AMP MAIN CIRCUIT BREAKER (778 9 FLA) ILLUMINATED EMERGENCY STOP MANUALLY OPERATED SIREN / SIGNAL - 250 HP IMPACTOR MOTOR 400 AMP CIRCUIT BREAKER ABB 300 HP RATED RVSS HOUR METER IN DOOR CONTROLS IN ENCLOSURE DOOR - 4812 VIBRATING PAN FEEDER (2) 8.5 HP MOTORS - RUN TOGETHER 60 AMP CIRCUIT BREAKER ABB ACS880 VARIABLE FREQUENCY DRIVE SPEED POTENTIOMETER INDIVIDUAL OVERLOADS - 1 PER MOTOR SERIES OVERLOADS TO DRIVE RUN SIGNAL CONTROLS IN ENCLOSURE DOOR - PRE-SCREEN MODULE (2) 4.3 HP MOTORS - RUN TOGETHER 25 AMP CIRCUIT BREAKER ABB ASC880 VARIABLE FREQUENCY DRIVE SPEED POTENTIOMETER INDIVIDUAL OVERLOADS - 1 PER MOTOR SERIES OVERLOADS TO DRIVE RUN SIGNAL CONTROLS IN ENCLOSURE DOOR - 6X16 SCREEN 80 AMP CIRCUIT BREAKER NEMA / IEC RATED SIZE 3 MOTOR STARTER CONTROLS IN ENCLOSURE DOOR - UNDER CRUSHER PAN FEEDER (2) 2.7 HP MOTORS - RUN TOGETHER (2) 15 AMP CIRCUIT BREAKERS (2) NEMA / IEC RATED SIZE 0 MOTOR STARTERS (1) SET OF CONTROLS SERIES OVERLOADS TO START / RUN SIGNAL CONTROLS IN ENCLOSURE DOOR - UNDER CRUSHER DISCHARGE 15 HP MOTOR 40 AMP CIRCUIT BREAKER NEMA / IEC RATED SIZE 2 MOTOR STARTER CONTROLS IN ENCLOSURE DOOR - SCREEN FINES CONVEYOR 15 HP MOTOR 40 AMP CIRCUIT BREKAER NEMA / IEC RATED SIZE2 MOTOR STARTER CONTROLS IN ENCLOSURE DOOR - CROSS CONVEYOR 1 7.5 HP MOTOR 20 AMP CIRCUIT BREAKER NEMA / IEC RATED SIZE 1 MOTOR STARTER CONTROLS IN ENCLOSURE DOOR - CROSS CONVEYOR 2 7.5 HP MOTOR 20 AMP CIRCUIT BREAKER NEMA/ IEC RATED SIZE 1 MOTOR STARTER CONTROLS IN ENCLOSURE DOOR - GRIZZLY FINES CONVEYOR 4.5 HP MOTOR 15 AMP CIRCUIT BREAKER NEMA / IEC RATED SIZE 0 MOTOR STARTER CONTROLS IN ENCLOSURE DOOR - RECIRCULATION CONVEYOR 10 HP MOTOR 25AMP CIRCUIT BREAKER NEMA / IEC RATED SIZE 1 MOTOR STARTER CONTROLS IN ENCLOSURE DOOR - 100 AMP FEED BREAKER WIRED TO A 100 AMP HUBBELL RECEPTACLE MATING PLUG INCLUDED - (2) 60 AMP FEED BREAKERS WIRED TO 60 AMP HUBBELL RECEPTACLES MATING PLUGS INCLUDED - 100- OF MAIN POWER CORD - INTERLOCKS ARE TO BE DETERMINED S/N#-S OF THE UNITS ARE BELOW: - 2463847 (CHASSIS) - 2463857 (4250 HSI) - 2463848 (6X12 ANTHEM) - 2463849 (48X12 VIBRATING PAN FEEDER) - 2463851 (4X6 PRE-SCREENER) - 2463853 (48X72 UNDER CRUSHER PAN FEEDER) - GUARDING FOR DRIVE AND TAIL PULLEYS V-BELT DRIVE AND RETURN IDLERS. GUARDS MAY NOT MEET ALL LOCAL CODES; CUSTOMER IS RESPONSIBLE TO HAVE GUARDING INSPECTED